I love these fingerless mittens - they are knitted with DK yarn, but the textured stitch pattern makes them thick and cosy.
A lovely little gift.
ORLA Fingerless Mittens Adult Woman
Requirements:
DK yarn ~ around 27g - 30g
5mm needles
Size:
Width: 7” (18cm) all around
Length: 7” (18cm)
Instructions:
Make 2 mittens the same
Cast on 37sts,
leaving a tail to use for joining
Row 1: S1, knit to end
Row 2: S1, purl to last st, k1
Row 3: S1, * k1, slip next stitch knitwise, repeat
from * to last 2sts, k2
Row 4: S1, * k1, take yarn to front, slip next
stitch purwise, and put yarn to back again, repeat from * to last 2sts, k2
Repeat the last
4 rows 14 times more or until work measures around 7”
Next Row: S1, knit to end
Cast off
knitwise, leaving a ‘tail’ to use for joining
Fold in half lengthwise. Using the
cast on tail, join the sides up to 3 inches. This is the bottom of the mitten.
Using the cast off tail, seam the sides up to 2 inches for the top of the
mitten. This should leave a 2 inch gap for the thumb.
Darn away ends
ORLA Fingerless Mittens Teenager / Small Adult
Requirements:
DK yarn ~ around 25g - 30g
5mm needles
Size:
Width:
6½" (16.5cm) all around
Length:
6¾" (17cm)
Instructions:
Make 2 mittens the same
Cast on 35sts leaving a tail to use for joining
Row 1: S1, knit to end
Row 2: S1, purl to last st, k1
Row 3: S1, * k1, slip next stitch knitwise, repeat
from * to last 2sts, k2
Row 4: S1, * k1, take yarn to front, slip next
stitch purwise, and put yarn to back again, repeat from * to last 2sts, k2
Repeat the last
4 rows until work measures around 6¾"
Next Row: S1, knit to end
Cast off
knitwise, leaving a ‘tail’ to use for joining
Fold in half lengthwise. Using the
cast on tail, join the sides up to 2¾ inches. This is the bottom of the mitten.
Using the cast off tail, seam the sides up to 2 inches for the top of the
mitten. This should leave a 2 inch gap for the thumb.
Darn away ends
ORLA Fingerless Mittens Child
–
Large
Requirements:
DK yarn around 22g - 26g
5mm needles
Size:
Width:
6¼" (16cm) all around
Length:
6½" (16.5cm)
Instructions:
Make 2 mittens the same
Cast on 33sts leaving a tail to use for joining
Row 1: S1, knit to end
Row 2: S1, purl to last st, k1
Row 3: S1, * k1, slip next stitch knitwise, repeat
from * to last 2sts, k2
Row 4: S1, * k1, take yarn to front, slip next
stitch purwise, and put yarn to back again, repeat from * to last 2sts, k2
Repeat the last
4 rows until work measures around 6½"
Next Row: S1, knit to end
Cast off
knitwise, leaving a ‘tail’ to use for joining
Fold in half lengthwise. Using the
cast on tail, join the sides up to 2½ inches. This is the bottom of the mitten.
Using the cast off tail, seam the sides up to 2 inches for the top of the
mitten. This should leave a 2 inch gap for the thumb.
Darn away ends
ORLA Fingerless Mittens Child
– Medium
Requirements:
DK yarn ~ around 20g - 24g
5mm needles
Size:
Width:
6" (15cm) all around
Length:
6" (15cm)
Instructions:
Make 2 mittens the same
Cast on 31sts leaving a tail to use for joining
Row 1: S1, knit to end
Row 2: S1, purl to last st, k1
Row 3: S1, * k1, slip next stitch knitwise, repeat
from * to last 2sts, k2
Row 4: S1, * k1, take yarn to front, slip next
stitch purwise, and put yarn to back again, repeat from * to last 2sts, k2
Repeat the last
4 rows until work measures around 6”
Next Row: S1, knit to end
Cast off
knitwise, leaving a ‘tail’ to use for joining
Fold in half lengthwise. Using the
cast on tail, join the sides up to 2½ inches. This is the bottom of the mitten.
Using the cast off tail, seam the sides up to 2 inches for the top of the
mitten. This should leave a 1½ inch gap for the thumb.
Darn away ends
ORLA Fingerless Mittens Child
–
Small
Requirements:
DK yarn ~ around 16g - 20g
5mm needles
Size:
Width:
5½" (14cm) all around
Length:
5" (13cm)
Instructions:
Make 2 mittens the same
Cast on 29sts leaving a tail to use for joining
Row 1: S1, knit to end
Row 2: S1, purl to last st, k1
Row 3: S1, * k1, slip next stitch knitwise, repeat
from * to last 2sts, k2
Row 4: S1, * k1, take yarn to front, slip next
stitch purwise, and put yarn to back again, repeat from * to last 2sts, k2
Repeat the last
4 rows until work measures around 5”
Next Row: S1, knit to end
Cast off
knitwise, leaving a ‘tail’ to use for joining
Fold in half lengthwise. Using the
cast on tail, join the sides up to 2 inches. This is the bottom of the mitten.
Using the cast off tail, seam the sides up to 1½ inches for the top of the
mitten. This should leave a 1½ inch gap for the thumb.
Darn away ends
Lovely pattern, thank you so much
ReplyDeleteFingerless mitts have become a favourite in my part of the world. Beautiful pattern x.
ReplyDelete